Profile: DustyBar8413

Your personal background.
“What questions do you think are going unanswered here?
Think that Kennmore Washers are expensive! Home warranties may make sense if appliances are
expensive to replace or nearing the end of their life span.
If you have a faulty home appliance, then you must not wait
until the minor issue can become major and unbearable. Also,
if I bought a replacement for the entire unit, I'd then have yet another set
of electronics without a meter! Common problems with older electronics
in general are dried up electrolytic capacitors, bad connections,
deteriorated wiring, and corrosion if used or stored under damp conditions.
Pressing "Load Hold" under normal conditions will override the
CVT-16 set-point and allow the load to be powered regardless of pressure.
Pressing "Reset" and "Load Hold" at the same time will override the fault
and allow the load to be powered should this be needed to remove the fault condition. It seems that no
two TC gauges ever use the same drive frequency! An off-center hole was drilled
and tapped for an 0-80 screw that would adjust the separation of the
two "leaves".

There were a grand total of two (2) caps (one for
half wave rectified line voltage and the other
for the low voltage derived from it - 4 uF at 150 WVDC and 20 uF at 10
WVDC). I have put TWO sections, further down this article,
for do it yourself-ers (DIY). The hands can be reversed by registering the lugs differentlyAll project content
written and produced by Mike Edwards, founder of DIY Doctor
and industry expert in building technology. With modern and scientific innovation there are various technology has evolved in different
types of fridges being in the market. Replacing them with slightly larger values from my used
but tested stock, totally cleaned up the drive signal which was a
bit over 0.3 V p-p, just about right for the DV-4D
TC gauge tube (there is an adjustment of this if needed).
This is actually my second TC gauge using a DV-4D tube.


I still would like to find a DV-4D for this or my other
gauge (which I also tested with the DV-4AM). It uses a DV-4D TC
gauge tube and has a useful range of 0.1 to 20 Torr so it
is for the upper end of medium vacuums. When I worked on repairing
this unit, I didn't yet have a TC gauge tube for either but was
able to look at the heater drive signal with an oscilloscope and inject a
low DC voltage to simulate the thermocouple output to test the meter
and amplifiers, if any (in this unit there are no amplifiers for the meter).
The main precautions to take are to avoid blowing out the meter or TC gauge tube
heater with excessive current - even measuring their resistance with an analog VOM on the low ohms range may be fatal.
Figuring that this was due to dried up electrolytic capacitors, I opened the back of the meter (all the circuitry is
on a printed circuit board inside a metal cover).
The schematic of the VT-4 (courtesy of Hastings) is shown in: Hastings VT-4/VT-6
Readout Circuit. Later, after noticing that the line regulation of
the simple zener circuit wasn't that great, and in addition, the reading was drifting as the gauge heated up,
I replaced the AC input circuitry with a low voltage power supply consisting of a
12.6 VRMS centertapped transformer, full wave rectifier, filter capacitor, and
LT1084 regulator set up for 6.0 VDC, which was slightly less than what
I measured across the zener but the adjustment pot had plenty of extra range and that allowed me to use a transformer I had gathering dust on my
transformer shelf.

Simply remove the filter cover and pull lower rack out to remove filter cover inside a dishwasher.

After removing the front cover and set-point mechanism, the extent of the damage could
be seen. It can be taken off by removing the screws and sliding it forward.

Avoid buying an automatic defrost freezer, which can decrease energy efficiency by up to 40%.

And if your freezer suddenly starts to take on a lot more frost,
or needs defrosting more than every couple of months, check the door again for a
good seal. Most customers don’t know this, have the inclination to investigate, or even want to
take a chance they’ll cause more problems than they already have.

For other responsibilities like marketing strategy
and distribution and just general maintenance, I'll have other amazing members
of my team take care of that. General Electric makes a wide range of
appliances that have given the homeowner an edge
that previous generations could only dream about.


my site - "https://Asteroidsathome.net/boinc/view_profile.php?userid=620289
Your feedback on this profile
Recommend this profile for User of the Day: I like this profile
Alert administrators to an offensive profile: I do not like this profile
Account data View
Team None


©2024 Progger & Stefano Tognon (ice00)