| Your personal background. |
|---|
A cold trap and a cryo trap are a must, and a gauge capable of measuring down to this range (e.g.,
ion gauge) is needed but without it you are blind.
For an argon ion laser the same cathode is often used on a 1 watt tube as in a 20 watt one - same
size made by the same company. A cathode isn't just a helix of
pure tungstan wire. My job involves making miniature thermionic cathode X-ray tubes, so I've had my share of
vacuum traumas. If you see the needle on your vacuum gauge twitch, you're close to
the leak. Just pump your system down as low as
it will go with your electronic vacuum gauge hooked up, and spray a little
helium at all the suspicious points in your system. Not to mention that most modern gas bottle
regulators will "run away" full open when exposed
to a vacuum. What is really needed is a very fine filter just before the gas
inlet or port to the cavity, but the commercial
ones are very expensive, so if you need one on a budget, look towards yours or your
neighbor's ink jet printer cartridges - the empty ones.
A basic vacuum/gas fill/bakeoff station to do a commercial tube might
cost $300,000 if bought new but the resulting laser tube will last years.
This, coupled with the poor vacuum facilities of the average amateur, means that any resulting laser tube would be just a experiment, not something you could seal off
and use. If you want to use the electronic gauge, you need to calibrate it
against a closed-end manometer using the laser mix gas.
Second, be aware that all it takes is ONE arc into your gauge, and there goes the
controller and probably the sensor (voice of experience).
Just thought I would throw in a bit of my experience
with vacuum systems. Its not as easy as the Scientific
American stuff says it is, Vacuum processing is an art for a SEALED OFF tube that is going to last awhile.
Now there’s a new call for action from fire
chiefs, backed by the Electrical Safety Council, which says there are “potentially millions” of faulty products
in homes. A plethora of sites now offer tips and advice on how to lead
a greener life. If that time is now for you or someone
that you know, contact one of our representatives today.
Contact us today so we can fix your broken Magic Chef Appliance.
There will probably be a little residue where it was secured to the plastic mounting, this can easily be
cut off, nice and clean by sharpening one end
a round metal tube that has the ID that you need. As for how to
mount this newly found ultra fine filter, you could push
it into a metal tube, then using a tubing cutter, like the ones used for
refrigeration & air conditioning, make two genital indented rings on the tube, one on each side of the filter and as close as possible to it.
Then, insert a blunt object into that hole in the bottom and
gently push the filter out. First, you'll need
to pull out the ink sponges by popping the top cap off the cartridge.
They come out of the cartridge pretty easy, just be sure to wear some disposable gloves and do this when either your wife,
husband or mother is not home. My Lexmark printer's cartridges contain one 11 mm diameter filter in the bottom, and the
color cartridge contains three smaller ones, about 6
mm diameter. Then, just lay the filter on some hard wood, or plastic, (not the kitchen counter) center the
tube punch coaxially with the filter and tap the tube with a hammer to cut the
filter.
For a tube that never leaves the pump, like most home-built lasers, you
can put in a fresh fill and flush away dirt. And if you're in need of wolf cooktop repair in West
Hills, we can handle that too! From Business: From Asurion Appliance Repair
We specialize in major appliance repairs including refrigerators, dishwashers, ovens/stoves, freezers,
washing machines, and… LG offers elegant and high-performing LG cooktops, with features including stainless steel trim,
SmoothTouch™ controls, induction bridge elements and premium-grade griddles; induction cooktops embody conceptual features like large-area bridge
elements that convert two heating elements into one - all of which AES expertly services.
Their appearance looks like stainless steel. It has a lot of different compounds sintered into it
when it's made and is more like a hollow sponge if you look at it under an electron microscope.
Helium has orders of magnitude more permeation through these substances than air.
Helium has a phenomenal heat conductivity, and can throw of the calibration by orders
of magnitude. The truth is that there is only so much that even the most skilled repairman can do about your appliances.
Look at my web-site: "http://Camillacastro.us/forums/profile.php?id=18805 |
| Your feedback on this profile |
|---|
| Recommend this profile for User of the Day: |
I like this profile |
| Alert administrators to an offensive profile: |
I do not like this profile |
|
| Account data |
View |
| Team |
None |
|
