| Your personal background. |
|---|
Pfeiffer pumps use precision steel dowels to align everything and
are about as simple as is possible in terms of the
number of individual components and the ease of servicing.
If the needle and spring pops out, it is a simple matter
to inspect the seat, needle, and spring.
This may not actually be attached to the needle itself but
if it isn't, the needle and spring should pop out when it
is removed. 9. Fridge runs too long: In this situation, check out key parts such as the thermostats or faulty defrost timer.
For those who have a self-defrosting unit, the initial location you should check would be the
condenser supporter. Hernández encourages kids who want
to be an astronaut to study STEM subjects. Safety valve electrical testing (if present) - If your Duo 1.5A has the "safety valve" feature, there will be a
4 pin connector on the lower right side of the bulkhead (facing the pump side).
This will confirm whether the vacuum performance is being affected by a defective safety valve.
However, leaving it like this may result in pump oil being
sucked into the vacuum chamber after shutdown and may also prevent the motor
from restarting if the system is under vacuum.
However, I can provide a PDF of the Uno/Duo 1.5 manual if needed.
However, this may be why the manual includes complete service info and exploded
assembly diagrams - not present on the Pfeiffer models
in current production. But they now only have manuals for pumps
still in production. 1992 R100R, transmission 0204810AA1, VIN WB1048701N0280119,
production of 10/15/1991, no groove, and hence no circlip.
The Uno/Duo 1.5A is considered an obsolete model but that doesn't make it any less useful as long as major repair
parts aren't needed. The complete operation and service manual for the Uno/Duo 1.5A used to be available at the Pfeiffer
Vacuum Web site. The following should apply in general to other model Pfeiffer rotary
vane two stage vacuum pumps with obvious changes in the details.
The base pressure of 4 to 5 microns wasn't terrible but is higher than the spec in the
manual - 0.66 micron (though I was told by a
Pfeiffer repair technician that 2 or 3 microns is really what to expect if everything is perfect.
I've seen requirements as high as 15 Torr or so for some types but
75 to 100 microns is probably more typical for this model.
For an inlet capped with just a vacuum gauge, a few dozen Torr may be typical.
Safety valve vacuum chamber valve inspection and testing (if present)
- Remove any vacuum system components attached to the inlet port.
Protect the inlet flange from tool damage and use a suitable wrench to unscrew it.
If the needle sticks inside, then use an adjustable wrench to unscrew the entire gas ballast valve assembly.
Gas ballast valve (if present) - Unscrew the knurled
valve handle. Experts are trained to handle such problems and fix problems quite easily.
Toasters, hair strengtheners, hair dryers, Hand
blenders, mini vacuum cleaners, are a few of all of these machines which are utilized on a
daily basis and are susceptible to a lot of wear & tear.
A set of metric hex wrenches, a medium size flat blade screwdriver, an adjustable wrench, needlenose pliers, and a few other
common hand tools are required. In an air conditioner, the common problem is with the condenser, if rapidly turned
on or off. If (1) is high but (2) is low or 0, there is a problem with the diodes or their wiring.
If both voltage are much higher, the solenoid of the safety valve is open or there is a bad connection in the wiring
to the solenoid. With the pump running, the voltage across pins 1 and 3 should be 3.5 to 4.5 VDC.
There is no need to go behind the connector if the following tests have acceptable results: - With the pump running, the
voltage across pins 2 and 4 should be 4.5 to 5.5 VRMS AC.
In most situations, the fridges are repaired on the very same day, but when there are parts to be replaced, there may me some
anticipated delay. From fridges to washers and everything in between, Amana has expanded their range to include
a number of essential home appliances. At JENN-AIR Repair
Center, we know that diagnostics are a huge part
of expert home appliance repair. Whatever the reason, buying a lightly used appliance can be a smart move as long as you know what to look
for and where to look for it. Look for "towers" and horizontal
cabinets that can be stacked in order to take advantage
of vertical space.
my homepage :: "http://www.security.sbm.pw/user/freemanpoo/ |
| Your feedback on this profile |
|---|
| Recommend this profile for User of the Day: |
I like this profile |
| Alert administrators to an offensive profile: |
I do not like this profile |
|
| Account data |
View |
| Team |
None |
|
