| Your personal background. |
|---|
“What questions do you think are going unanswered here?
Think that Kennmore Washers are expensive! Home warranties may make sense
if appliances are expensive to replace or nearing the end of their life
span. If you have a faulty home appliance, then you must not
wait until the minor issue can become major and unbearable.
Also, if I bought a replacement for the entire unit, I'd then have yet another set of electronics
without a meter! Common problems with older
electronics in general are dried up electrolytic capacitors, bad connections,
deteriorated wiring, and corrosion if used or stored under
damp conditions. Pressing "Load Hold" under normal conditions will override the CVT-16 set-point and allow
the load to be powered regardless of pressure. Pressing "Reset" and "Load Hold" at the same time will override the fault and
allow the load to be powered should this be needed to remove the fault condition.
It seems that no two TC gauges ever use the same drive frequency!
An off-center hole was drilled and tapped for an 0-80 screw
that would adjust the separation of the two "leaves".
There were a grand total of two (2) caps (one for half wave rectified line
voltage and the other for the low voltage derived from it - 4 uF at 150 WVDC and 20 uF at 10 WVDC).
I have put TWO sections, further down this article, for do it yourself-ers (DIY).
The hands can be reversed by registering the lugs differentlyAll
project content written and produced by Mike Edwards, founder of DIY Doctor and industry expert in building technology.
With modern and scientific innovation there are various technology has
evolved in different types of fridges being in the market.
Replacing them with slightly larger values from my used but tested stock, totally cleaned up the
drive signal which was a bit over 0.3 V p-p,
just about right for the DV-4D TC gauge tube (there
is an adjustment of this if needed). This is actually my second TC gauge using a DV-4D tube.
I still would like to find a DV-4D for this or my other gauge
(which I also tested with the DV-4AM). It uses a DV-4D TC gauge tube and has a useful range of 0.1 to 20 Torr so it is
for the upper end of medium vacuums. When I worked on repairing read
this blog article from www.capital.bookmarking.site unit, I didn't yet have
a TC gauge tube for either but was able to look at the heater drive signal with an oscilloscope and inject a low DC
voltage to simulate the thermocouple output to test the meter and amplifiers, if any
(in this unit there are no amplifiers for the meter).
The main precautions to take are to avoid blowing out the meter or TC gauge tube heater with excessive current - even measuring their resistance with an analog VOM on the low ohms range may be fatal.
Figuring that this was due to dried up electrolytic capacitors, I opened the back of the meter
(all the circuitry is on a printed circuit board inside
a metal cover). The schematic of the VT-4 (courtesy of Hastings) is shown in: Hastings VT-4/VT-6 Readout Circuit.
Later, after noticing that the line regulation of the simple zener circuit wasn't that great,
and in addition, the reading was drifting as the gauge heated up, I replaced the AC input circuitry with a low voltage power supply consisting of a 12.6 VRMS centertapped transformer, full wave rectifier, filter
capacitor, and LT1084 regulator set up for 6.0 VDC, which was
slightly less than what I measured across the zener but the adjustment pot had plenty of extra range and that allowed me to use a transformer I had gathering dust on my
transformer shelf.
Simply remove the filter cover and pull lower rack out to remove filter cover
inside a dishwasher. After removing the front cover and set-point
mechanism, the extent of the damage could be seen. It can be taken off by removing the screws and sliding it forward.
Avoid buying an automatic defrost freezer, which can decrease energy efficiency by up
to 40%. And if your freezer suddenly starts to take on a lot more frost,
or needs defrosting more than every couple of months, check the door again for a good seal.
Most customers don’t know this, have the inclination to
investigate, or even want to take a chance they’ll cause more problems than they already have.
For other responsibilities like marketing strategy and distribution and just
general maintenance, I'll have other amazing members of my team take care of that.
General Electric makes a wide range of appliances that have given the homeowner an edge that previous generations could only dream about. |
| Your feedback on this profile |
|---|
| Recommend this profile for User of the Day: |
I like this profile |
| Alert administrators to an offensive profile: |
I do not like this profile |
|
| Account data |
View |
| Team |
None |
|
